28
авг
Traditional door locks work just fine, but if you want to add some smarts to the security of your home, a smart lock is a good way to go. Here’s how to install and set up the. Before you get started, make sure that replacing a deadbolt is something that you’re comfortable doing. It’s pretty easy for the most part, but it does involve removing the entire deadbolt mechanism and replacing it with an all-new one. So if you’re not quite sure how comfortable you’d be doing something like that, it may be wise to call in reinforcements and have a knowledgeable friend (or a professional locksmith) help. This guide also assumes that you already have a deadbolt installed on your door. If you don’t, then you’ll need to drill a completely new hole in your door to install the Kevo (or any deadbolt for that matter) using.
Reset Tool For Schlage Securekey™ And Kwikset Smartkey™ New tool designed to reset the Schlage Securekey™ and Kwikset Smartkey™ cylinders when you do not have a working key available. Consists of two combs; one on each end of the tool. To add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Procedure continued on next page 62543 / 01 3 / 13 Technical Support 1-800-327-5625 www.kwikset.com C Adding User Codes with the Mastercode Enabled.
Luckily, the Kwikset Kevo kit comes with all of the materials that you’ll need, but you’ll need a couple of tools to put it all together: a screwdriver or power drill, and maybe a hammer. Step One: Remove Your Existing Deadbolt Start by removing the current deadbolt that’s installed on the door, which usually involves removing a couple of screws from the inside. After those screws are removed, carefully take off the cover. You may have to slightly tap on it with a hammer to loosen it up if it doesn’t come off easily. There will two more screws on the inside that you’ll need to remove. These connect the inside portion of the lock to the outside portion.
Once those screws are removed, you can carefully pull apart the entire lock and remove it, starting with the interior section. From there, remove the outside portion. Next, remove the two screws on the latch. Pull the latch out of the door. You now have a clean slate to install the Kevo smart lock.
Step Two: Install the Kwikset Kevo First off, Kwikset says that you can follow installation instructions within the Kevo app on your phone. However, to prevent your phone from getting dirty or damaged during the installation process, we recommend instead and keeping your phone safe throughout this stage. Or better yet, follow our instructions below. The first step is to install the new door latch. There are two that come included with the kit; one with a plate and one without, depending on your door. Take a look at your previous door latch and match it with the new one to see which one you need to use. Insert the door latch into the door.
Make sure that the middle hole in the door latch is centered within the door’s hole. If not, remove the latch, hold onto the deadbolt latch and rotate the mechanism 180 degrees to change the position of the middle hole. Re-insert the latch, making sure the “UP” marking on the latch is facing up.
Secure the latch to the door using the two screws in the pouch marked “03809”. Next, measure the diameter of the door hole. If it’s the standard 2-1/8″ measurement, you’ll need the adapter ring. Slide it onto the inside of the Kevo lock with the tabs facing out. After that, measure the thickness of the door. If it’s 1-3/8″ thick, use the shorter screws in the pouch marked “19571”.
If it’s 1-3/4″ thick, use the longer screws. You’ll need them handy a couple of steps later. Place the Kevo lock onto the door, feeding the cable underneath the latch and inserting the rod through the middle latch hole, making sure to line up the shape in order to get it in. On the other side, place the mounting plate over the hole and feed the cable through it.
Jimmy castor e man groovin rar. Take the two screws (either the short or long ones) and insert them through the mounting plate and into the Kevo lock on the other side. Use your screwdriver or power drill to tighten them.
This will securely affix the Kevo lock to your door. Next, take the key included in the kit and insert it into the lock, making sure that the deadbolt extends and retracts freely. Moving on, separate the interior cover from the interior mechanism and remove the battery pack. Connect the cable from the Kevo lock to the interior mechanism. Tuck the cable into the interior mechanism the best you can and slide the whole thing onto the lock’s rod from the other side and mount everything in place.
Popular Posts
Traditional door locks work just fine, but if you want to add some smarts to the security of your home, a smart lock is a good way to go. Here’s how to install and set up the. Before you get started, make sure that replacing a deadbolt is something that you’re comfortable doing. It’s pretty easy for the most part, but it does involve removing the entire deadbolt mechanism and replacing it with an all-new one. So if you’re not quite sure how comfortable you’d be doing something like that, it may be wise to call in reinforcements and have a knowledgeable friend (or a professional locksmith) help. This guide also assumes that you already have a deadbolt installed on your door. If you don’t, then you’ll need to drill a completely new hole in your door to install the Kevo (or any deadbolt for that matter) using.
Reset Tool For Schlage Securekey™ And Kwikset Smartkey™ New tool designed to reset the Schlage Securekey™ and Kwikset Smartkey™ cylinders when you do not have a working key available. Consists of two combs; one on each end of the tool. To add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Procedure continued on next page 62543 / 01 3 / 13 Technical Support 1-800-327-5625 www.kwikset.com C Adding User Codes with the Mastercode Enabled.
Luckily, the Kwikset Kevo kit comes with all of the materials that you’ll need, but you’ll need a couple of tools to put it all together: a screwdriver or power drill, and maybe a hammer. Step One: Remove Your Existing Deadbolt Start by removing the current deadbolt that’s installed on the door, which usually involves removing a couple of screws from the inside. After those screws are removed, carefully take off the cover. You may have to slightly tap on it with a hammer to loosen it up if it doesn’t come off easily. There will two more screws on the inside that you’ll need to remove. These connect the inside portion of the lock to the outside portion.
Once those screws are removed, you can carefully pull apart the entire lock and remove it, starting with the interior section. From there, remove the outside portion. Next, remove the two screws on the latch. Pull the latch out of the door. You now have a clean slate to install the Kevo smart lock.
Step Two: Install the Kwikset Kevo First off, Kwikset says that you can follow installation instructions within the Kevo app on your phone. However, to prevent your phone from getting dirty or damaged during the installation process, we recommend instead and keeping your phone safe throughout this stage. Or better yet, follow our instructions below. The first step is to install the new door latch. There are two that come included with the kit; one with a plate and one without, depending on your door. Take a look at your previous door latch and match it with the new one to see which one you need to use. Insert the door latch into the door.
Make sure that the middle hole in the door latch is centered within the door’s hole. If not, remove the latch, hold onto the deadbolt latch and rotate the mechanism 180 degrees to change the position of the middle hole. Re-insert the latch, making sure the “UP” marking on the latch is facing up.Secure the latch to the door using the two screws in the pouch marked “03809”. Next, measure the diameter of the door hole. If it’s the standard 2-1/8″ measurement, you’ll need the adapter ring. Slide it onto the inside of the Kevo lock with the tabs facing out. After that, measure the thickness of the door. If it’s 1-3/8″ thick, use the shorter screws in the pouch marked “19571”.
If it’s 1-3/4″ thick, use the longer screws. You’ll need them handy a couple of steps later. Place the Kevo lock onto the door, feeding the cable underneath the latch and inserting the rod through the middle latch hole, making sure to line up the shape in order to get it in. On the other side, place the mounting plate over the hole and feed the cable through it.
Jimmy castor e man groovin rar. Take the two screws (either the short or long ones) and insert them through the mounting plate and into the Kevo lock on the other side. Use your screwdriver or power drill to tighten them.
This will securely affix the Kevo lock to your door. Next, take the key included in the kit and insert it into the lock, making sure that the deadbolt extends and retracts freely. Moving on, separate the interior cover from the interior mechanism and remove the battery pack. Connect the cable from the Kevo lock to the interior mechanism. Tuck the cable into the interior mechanism the best you can and slide the whole thing onto the lock’s rod from the other side and mount everything in place.
...'>Resetting Powermax Installer Code For Kwikset(28.08.2018)Traditional door locks work just fine, but if you want to add some smarts to the security of your home, a smart lock is a good way to go. Here’s how to install and set up the. Before you get started, make sure that replacing a deadbolt is something that you’re comfortable doing. It’s pretty easy for the most part, but it does involve removing the entire deadbolt mechanism and replacing it with an all-new one. So if you’re not quite sure how comfortable you’d be doing something like that, it may be wise to call in reinforcements and have a knowledgeable friend (or a professional locksmith) help. This guide also assumes that you already have a deadbolt installed on your door. If you don’t, then you’ll need to drill a completely new hole in your door to install the Kevo (or any deadbolt for that matter) using.
Reset Tool For Schlage Securekey™ And Kwikset Smartkey™ New tool designed to reset the Schlage Securekey™ and Kwikset Smartkey™ cylinders when you do not have a working key available. Consists of two combs; one on each end of the tool. To add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Procedure continued on next page 62543 / 01 3 / 13 Technical Support 1-800-327-5625 www.kwikset.com C Adding User Codes with the Mastercode Enabled.
Luckily, the Kwikset Kevo kit comes with all of the materials that you’ll need, but you’ll need a couple of tools to put it all together: a screwdriver or power drill, and maybe a hammer. Step One: Remove Your Existing Deadbolt Start by removing the current deadbolt that’s installed on the door, which usually involves removing a couple of screws from the inside. After those screws are removed, carefully take off the cover. You may have to slightly tap on it with a hammer to loosen it up if it doesn’t come off easily. There will two more screws on the inside that you’ll need to remove. These connect the inside portion of the lock to the outside portion.
Once those screws are removed, you can carefully pull apart the entire lock and remove it, starting with the interior section. From there, remove the outside portion. Next, remove the two screws on the latch. Pull the latch out of the door. You now have a clean slate to install the Kevo smart lock.
Step Two: Install the Kwikset Kevo First off, Kwikset says that you can follow installation instructions within the Kevo app on your phone. However, to prevent your phone from getting dirty or damaged during the installation process, we recommend instead and keeping your phone safe throughout this stage. Or better yet, follow our instructions below. The first step is to install the new door latch. There are two that come included with the kit; one with a plate and one without, depending on your door. Take a look at your previous door latch and match it with the new one to see which one you need to use. Insert the door latch into the door.
Make sure that the middle hole in the door latch is centered within the door’s hole. If not, remove the latch, hold onto the deadbolt latch and rotate the mechanism 180 degrees to change the position of the middle hole. Re-insert the latch, making sure the “UP” marking on the latch is facing up.Secure the latch to the door using the two screws in the pouch marked “03809”. Next, measure the diameter of the door hole. If it’s the standard 2-1/8″ measurement, you’ll need the adapter ring. Slide it onto the inside of the Kevo lock with the tabs facing out. After that, measure the thickness of the door. If it’s 1-3/8″ thick, use the shorter screws in the pouch marked “19571”.
If it’s 1-3/4″ thick, use the longer screws. You’ll need them handy a couple of steps later. Place the Kevo lock onto the door, feeding the cable underneath the latch and inserting the rod through the middle latch hole, making sure to line up the shape in order to get it in. On the other side, place the mounting plate over the hole and feed the cable through it.
Jimmy castor e man groovin rar. Take the two screws (either the short or long ones) and insert them through the mounting plate and into the Kevo lock on the other side. Use your screwdriver or power drill to tighten them.
This will securely affix the Kevo lock to your door. Next, take the key included in the kit and insert it into the lock, making sure that the deadbolt extends and retracts freely. Moving on, separate the interior cover from the interior mechanism and remove the battery pack. Connect the cable from the Kevo lock to the interior mechanism. Tuck the cable into the interior mechanism the best you can and slide the whole thing onto the lock’s rod from the other side and mount everything in place.
...'>Resetting Powermax Installer Code For Kwikset(28.08.2018)